• Skip to main content
  • Skip to footer
800.669.8871
Cart
Login
  • Store Policy
  • Contact
  • Products
  • Ask The Glue Experts
  • V&S Sprays
  • Store Policy
  • Blog
  • My Account
  • Contact

GluePlace

Selling Glue Since 1978

  • Products
  • Ask The Experts
  • V&S Sprays
Home | Products | Tensorgrip® P302 Non-Flam Contact Adhesive 22 Liters Kit with Hose and Gun

Tensorgrip® P302 Non-Flam Contact Adhesive 22 Liters Kit with Hose and Gun

$465.00

Only 2 left in stock

Category: Contact Adhesives
  • Description
  • Additional information

Description

Tensorgrip® P302 Non-Flam Contact Adhesive 22 Liters container (5.81 gallons) Kit includes 12″ hose, 23L-B Spray Gun and Tip

Only ships to business addresses. No PO BOX or Residencial

Tensorgrip® P302

Tensorgrip® P302 is a non-flammable, high performance industrial spray contact adhesive formulated for general contact bonding. Designed to deliver a smooth and strong bond in nearly any application while maintaining perfect non-flammable properties with leading Zero-Flam Technology.
Non-flammable solvent and non-flammable propellant.
Fast – High Tack • Fast drying with long open time • Good heat resistance (up to 220°F/105°C) • VOC free • Qualifies for LEED®-NC & CI EQ Credit 4.4:  laminating adhesives shall contain no urea formaldehyde resins.

Aplications:

Bonds veneers, fabrics, upholstery, foam, headliners, cork, fiberglass and many plastics.

Use where smoothness is required (e.g. glossy or thin laminate, fabrics)

Laminating flexible material in nearly any application.

Not Compliant in certain California Air Quality Districts

TENSORGRIP® P302 is designed as a portable, self-contained spray system for field or shop applications. Adhesive should be applied to both surfaces to be bonded, allowed to dry (2-4 minutes or until dry to touch) then parts mated under pressure. Bonds should be made as soon as practical. If adhesive is left to dry for over 30 minutes, parts should be recoated. Normal coverage required with lacing spray pattern is approximately 80%; however porous surfaces may need a second coat. Initial bond is strong enough to allow cutting or trimming immediately although ultimate strength is achieved in 1-3 days. Canister system will spray adequately above 60º F. Canister system should be kept in warm area. In the event that the canister gets abnormally chilled, freezes or gives poor or sputtering spray, it should be warmed up before continued usage. Warming canister by immersion in warm water is recommended. Notice!!! Avoid direct flame or exposure to excessive heat. Do not store at temperatures over 120º F. Not for use on flexible vinyl or polystyrene foam. Canister System Usage:  When hose is connected, keep canister valve open and hose pressurized at all times.  Do not disconnect the hose until ready to connect to new canister.  Release pressure in hose before disconnecting from canister.  If gun and hose must be stored unattached to pressurized canister, they may be cleaned for future use by attaching to canister of 609 Citrus cleaner and flushing until clear.

Canister Adhesives
Canister adhesives are designed as portable, self-contained spray systems for field or shop applications.  No outside air source is required.  The only equipment needed is a hose and spray gun.  However, compressed air may be used to improve sprayability and increase dry times.  Typically these are not big issues as canister adhesives are quite fast dry with extended open times allowing for sufficient workability.

These adhesives are available in 7Liter Mini – 22Liter Large – 108Liter Intermediate – 216Liter Jumbo size canisters.
Transfer efficiency of canister adhesives is <90%.
Transfer efficient.

Additional information

Weight 36 lbs
Dimensions 18 × 12 × 12 in

Footer

Need help finding the right solution? Call 800.669.8871 or contact us online

©2023, Adhesive Solutions, Inc
  • Products
  • Ask The Experts
  • V&S Sprays
800.669.8871
10106 Romandel Ave, Santa Fe Springs, CA 90670